Geothermal Heat Pumps Dayton OH

This page provides relevant content and local businesses that can help with your search for information on Geothermal Heat Pumps. You will find informative articles about Geothermal Heat Pumps, including "What are Ground-Source Heat Pumps". Below you will also find local businesses that may provide the products or services you are looking for. Please scroll down to find the local resources in Dayton, OH that can help answer your questions about Geothermal Heat Pumps.

Butler Heating & Air Condition
(937) 253-8871
120 Springfield St
Dayton , OH
Outstanding Heating & Air
(937) 439-4696
4701 Presidential Dr
Kettering , OH
Kirkwood Htg & Clg Inc
(937) 845-0500
7051 E Singer Rd
Dayton , OH
Detmer & Sons
(937) 879-2373
1170 Channing Way Dr
Fairborn , OH
Shawnee Heating & Air LLC
(937) 372-4471
658 Cincinnati Ave
Xenia , OH
William Brockman & Sons
(937) 222-8638
114 Valley St
Dayton , OH
HS Stevenson & Sons- Springfield
(937) 431-1523
799 Space Dr
Beavercreek , OH
Del-Monde Inc
(937) 847-8711
2485 Belvo Road
Miamisburg , OH
Allied Services Inc
(937) 836-5191
109 S Diamond Mill Rd
Clayton , OH
Simpson Htg & Cooling
(330) 339-1177
828 Maple Ave NW
ew Philadelphia, OH

What are Ground-Source Heat Pumps

Ground-source heat pumps, often called geo-thermal heat pumps, tap into the earth or a source of water for residual heat. There are all kinds of ways to connect the heat pump with the ground. In most cases, loops of plastic tubing filled with a nonfreezing fluid are buried in trenches that may stretch hundreds of feet around a building site. Tubing can also be dropped into one or more vertical walls, a technique that takes a lot less room but can be quite costly. Tubing can be placed at the bottom of a nearby pond, or water from a well can be the source of latent heat.

Types of Ground-Source Heat Pumps

Horizontal Ground-Linked Heat Pump

Tubing filled with antifreeze absorbs heat from the ground and carries it to a ground-source heat pump. Even in winter, underground temperatures are high enough to allow the system to work, but hundreds of feet of tubing must be buried and excavation can be extensive.

Open-Loop System Where Water is Abundant

With an open-loop system, water is pumped from a well through the heat pump and returned to earth. It passes through the system only once. If the well produces enough water, it can be used for both domestic supplies and the heat pump.

Closed-Loop Vertical System Recirculates Same Fluid

Tubing can be placed in one or more vertical wells if there isn't enough room for horizontal trenches. The number and depth of the wells depends on a variety of factors. A closed loop of nonfreezing liquid absorbs heat from the earth and moves it to the heat pump inside, where it is concentrated and distributed around the house.

Comparing Heat Pump Performance

The highest performing ground-source heat pumps on the market offer excellent energy savings over their lifetime-at least on paper. In one simulation from the U.S. Department of Energy, the most efficient heat pump was expected to use only about one third of the energy for heating as a standard air-source heat pump, 10,900kWh vs. 29,800kWh. Savings for cooling were not quite as dramatic, but overall the simulation estimated that annual energy savings were better than 2 to 1 with the ground-source heat pump.

However, anecdotal evidence suggests that ground-source heat pumps can be finicky and disappointing. Efficiency is described as a coefficient of performance (COP) which is the heating capacity  of the device in Btu divided by the electrical input.

A heat pump with a COP of 4 produces 4 units of energy for every 1 unit of electrical energy it co...

Click here to read the rest of this article from